The most damaging car towing mistakes include choosing the wrong towing method, dragging locked wheels, attaching equipment to unsuitable parts and loading a vehicle without enough ground clearance. You can reduce these risks by checking your owner's manual, telling the operator about any faults and confirming how they'll load and secure your car before work starts.
Choosing the wrong towing method
A wheel-lift truck raises one end of your car while the other wheels roll on the road. A flatbed carries the whole vehicle, while wheel dollies support wheels that would otherwise remain on the ground. You can't use these methods interchangeably on every vehicle.
On some vehicles, rolling the driven wheels with the engine off can turn transmission components without adequate lubrication. You can also damage all-wheel-drive and four-wheel-drive systems if one axle turns while the other stays stationary. Neutral doesn't automatically make towing safe.
Check your manual's instructions for towing a disabled vehicle, not just its recreational towing section. Restrictions can depend on the exact transmission, drivetrain and transfer-case configuration, so advice for a similar-looking car may be wrong.
Electric and hybrid vehicles also need model-specific procedures. Some require all wheels off the ground, and a transport mode may permit only the short movement needed for loading. If you can't confirm the approved method, request equipment that can lift every wheel and ask the operator to verify the loading procedure.
Dragging locked wheels
Winching your car while its transmission remains in Park, its parking brake is on or its brakes have seized can damage tyres and put excessive strain on mechanical parts. A flatbed won't prevent this damage if the operator drags your car onto it incorrectly.
Tell the operator if you've lost the keys, the battery is flat, the selector won't move or a wheel won't turn. The operator may need to follow an approved release procedure or use a suitable power supply to release electronic parking brakes and shift locks.
Don't force the selector or crawl underneath an unsupported vehicle to release anything. The operator may need wheel skates or dollies to move your car without dragging locked tyres across the ground.
A steering lock creates another problem if your car needs to turn during recovery. Explain any steering fault before the operator starts pulling, especially after an impact that may have bent a wheel or suspension component.
Using the wrong attachment points
A suspension arm, steering rod or convenient opening in the body isn't automatically a safe place for a hook. Pulling from an unsuitable point can bend components, tear metal or damage nearby brake hoses and wiring.
Ask the operator to explain which attachment points are recovery points and tie-down points. A point approved for pulling your car onto a truck may not be approved for securing it during transport. Likewise, a screw-in towing eye may have restrictions on pull direction, and the operator must fit it according to the manual.
Before loading, confirm that the operator will follow these precautions:
- Use only attachment points approved for the intended pull or restraint.
- Keep hooks, cables and straps clear of brake lines, electrical cables and body panels.
- Use wheel restraints that suit the tyre size and transport equipment.
- Protect any permitted contact points from abrasion and sharp edges.
- Secure loose or damaged bodywork so it can't move during transport.
The operator must secure your car against movement, not just stop it from rolling backwards. The Federal Motor Carrier Safety Administration's cargo securement rules explain how operators must restrain commercial loads against movement and include specific provisions for automobiles.
Loading without enough ground clearance
A steep loading angle can scrape your front bumper, splitter, exhaust or underbody panels. Your car can also scrape against the truck where the ramps meet the bed, particularly if it has a long wheelbase or lowered suspension.
Tell the operator about low ground clearance, aftermarket bodywork and suspension faults before they position the truck. A damaged or deflated tyre can lower one corner enough to affect how much clearance your car needs.
The operator may need a lower-angle bed, suitable ramp extensions or another loading method. Ask them to stop if a bumper or underbody component begins to touch. Pulling harder with the winch won't solve a clearance problem.
Unloading needs the same care. Confirm that the destination has enough clear, firm space for the truck and ramps, rather than assuming the operator can unload your car anywhere.
What can damage your car during transport?
A truck's size alone doesn't prove it can carry your car. The operator must account for your vehicle's actual weight, equipment capacity, axle loads and any additional cargo. Tell them about heavy modifications or a substantial load inside your car.
Straps with insufficient load capacity, damaged hooks and defective dollies can fail even when the truck itself has enough capacity. Leave lifting and restraint choices to a trained recovery operator, but ask for an explanation if equipment appears damaged or your car sits unevenly.
Pay particular attention to tyres that will remain on the road. The National Highway Traffic Safety Administration advises following your vehicle manufacturer's tyre-pressure recommendations and respecting load limits. Tell the operator about a puncture, sidewall damage or a wheel that struck an obstacle.
Sudden acceleration, harsh braking and sharp turns put extra strain on the restraints and can cause a poorly secured vehicle to shift. Keep passengers out of your car during transport and use only the passenger seating permitted in the recovery vehicle.
Skipping towing inspections
Photograph your car before loading, provided you can do so from a safe position away from traffic and moving equipment. Record existing damage so you can identify any new damage after recovery.
- Photograph bumpers, wheels, sills and visible damaged areas.
- Tell the operator about leaks, warning lights and mechanical faults.
- Confirm the towing method and any manufacturer restrictions.
- Check that loose belongings and detached parts are secure.
- Inspect your car again after the operator has unloaded it safely.
Before driving away, look for fresh leaks, displaced panels, tyre damage or hanging components. Report new damage promptly and keep your photographs and recovery paperwork. If you notice new vibration, steering problems, grinding noises or warning lights, stop driving and ask a qualified technician to inspect your car.
Sources
- Cargo Securement Rules · FMCSA (fmcsa.dot.gov)
- Tire Safety Ratings and Awareness · TireWise · NHTSA (nhtsa.gov)